FCD-IP
E1/T1 or Fractional E1/T1 Access Unit with Integrated Router

Features

•  E1/T1 access over copper, SHDSL or fiber.
•  One or two independent Ethernet ports or alternatively an integrated 4-port switch.
•  IP/IPX routing and transparent bridging.
•  Support of Frame Relay (RFC 1490) and PPP protocols.
•  OSPF support.
•  Optional data port.
•  Data Interfaces: V.35, RS-530, V.36/RS-449, V.24, X.21.
•  Selectable sync data rates: n x 56 kbps, n x 64 kbps.
•  Optional sub-E1/T1 port or four analog ports (FXS, FXO, E&M) for PBX/phone connectivity.
•  Fail-safe sub-E1/T1 ensures uninterrupted service.
•  Dial backup over ISDN/PSTN.
•  Operates with RAD’s DXC multiservice access node for multilink star configuration.
•  SNMP, Telnet or control port management.

RICi-E1/T1
E1, T1 Interface Converters

Features

•  Convert from V.35, X.21, V.36, RS-530 to E1 or T1 interfaces.
•  Connect 10BaseT and 100BaseT LANs and VLANs over E1 or T1 services.
•  Integrated IP router for connecting IP domains over E1/T1 services.
•  10/100BaseT bridge supporting IEEE 802.3x flow control and backpressure.
•  Diagnostic loopback activation in compliance with ITU V.54 standard.
•  Available as cards for RAD's ASM-MN-214 card cage.
•  Plug and play.

RICi-4E1L / 8E1L

Features

•  Connecting Fast Ethernet LANs over up to four or eight bonded E1 or T1 circuits.
•  Bonding four or eight E1 or T1 ports utilizing Multi-Link PPP, bridging the bandwidth gap between E1/T1 and E3/T3.
•  VLAN tagging, stacking and stripping fully separates Ethernet user traffic from management data.
•  Monitoring diagnostic tools for quick fault isolation on TDM and Ethernet ports.
•  Fault propagation of MLPPP errors to the Ethernet port.

ASM-31
2-Wire All Rate Short Range Modem

Features

•  2-wire, all-rate short range modem.
•  Single sync/async channel.
•  Full duplex operation using "echo cancellation".
•  Selectable data rates:
  •  Sync: 600 bps to 128 Kbps.
  •  Async: up to 115.2 Kbps.
•  2B1Q Line coding.
•  Operating range up to 5.5 km (3.4 miles), independent of data rate.
•  Diagnostics include internal BERT, local and remote test.
•  DTE interfaces: V.24/RS-232, V.35, G.703, RS-530 or X.21.
•  UTP or routing interface.

ASMI52
2/4 Wire SDHL Modem

Features

ASMi-52 is an SHDSL modem/multiplexer for data and voice that operates in full-duplex mode over 2-wire and 4-wire lines.

Multiple data rates in the range of 64 to 4608 kbps are supported. The data rates depend on the line interface, DTE interface types, and operating clock modes.

ASMi-52 employs standard SHDSL TC-PAM technology to extend the transmission range (see Table 1), thus enabling carriers to reach more customers at lower costs.

ASMI54
G.SHDSL.bis modem for high-speed access over copper

Features

ASMi-54 is a simple, cost-effective, dedicated managed G.SHDSL.bis modem that extends the range of high-speed services over existing copper pairs.

Using TC-PAM 16 or TC-PAM 32 line coding SHDSL.bis technology, the modem can operate in full-duplex mode over 2-wire lines at data rates of up to 5.7 Mbps.

ASMi-54 is used for point-to-point Ethernet service extension at rates of up to 22 Mbps using bonding technology.

RIC-E1, RIC-T1
E1 or T1 Converters

Features

•  Converts between V.35, X.21, V.36, RS-530, Etheret/Fast Ethernet bridge or IP router to unframed E1 or T1 interfaces.
•  2048 Mbps bit rate in E1 and 1.544 Mbps in T1.
•  Available as a standalone unit or as a card for the ASM-MN-214 rack.
•  Receive, internal and external clocking options.
•  V.54 diagnostic loop.
•  AC or DC power supply.